Fleet Hero

Transport Chains (G70 & G80)

7 products

Browse Subcategories

All Transport Chains (G70 & G80) Products

Filters

$
—
$

7 products

What Is Transport Chain?

Transport chain is the heavy-duty steel chain truckers use to lock down loads on flatbeds. It’s heat-treated carbon steel built for cargo control, not lifting. Most call it binder chain or G70 chain. NACM rates Grade 70 at 700 N/mm² tensile strength; Grade 80 sits higher at 800.

You’ll spot Grade 70 by its yellow chromate finish and the 7 or 70 stamped on the links. Grade 80 is usually black and marked 8.

Types of Transport Chain We Carry

  • Grade 70 chain assemblies with a clevis grab hook on each end, in 5/16", 3/8" and 1/2", cut to 16 ft, 20 ft and 25 ft for flatbed tie-down work.

  • Grade 80 alloy chain tie-downs for haulers who want more WLL at the same size - 7,100 lb at 3/8", 12,000 lb at 1/2" - sold with grab hooks, so securement only.

  • Clevis grab hooks have a shallow throat that grips one link and slips through a rub rail; clevis slip hooks with latch have a wide mouth for D-rings plus a latch against accidental release.

  • Bulk drum chain for shops cutting their own: roughly 550 ft of 5/16", 400 ft of 3/8", 200 ft of 1/2".

  • Case quantities for fleets re-chaining several trailers at once.

Chain Grades, Sizes and WLL Specs

Working load limits come straight from 49 CFR 393.108 Table 1 and NACM. Buy and secure by WLL-never by break strength.

Size

Grade 70 WLL

Grade 80 WLL

5/16"

4,700 lb

4,500 lb

3/8"

6,600 lb

7,100 lb

1/2"

11,300 lb

12,000 lb

A 3/8" G70 breaks at no less than 26,400 lb (4× WLL). Proof test is twice WLL. Grade 70 is heat-treated carbon steel; Grade 80 is alloy. Unmarked chain drops to Grade 30 roadside.

Where Drivers Use Transport Chain

You see Grade 70 chain on almost every flatbed, step-deck, RGN, lowboy and hotshot. It’s the stuff that holds excavators, skid steers, steel coils, plate and lumber when straps would just get cut up.

FMCSA says the total working load limit of your tie-downs has to reach at least half the cargo weight. A chain that goes over the load counts full WLL. One that runs straight from the D-ring to the cargo only counts half.

Four 3/8" G70 chains hooked direct to a 26,000 lb machine give you 13,200 lb of aggregate WLL- enough to clear the 13,000 lb mark. Two chains for anything under 10 ft, then one more for every extra 10 ft.

Same chain gets used for recovery bridles, logging and oilfield moves.

How to Choose and Inspect Transport Chain

A tie-down is only as strong as its weakest component, and under 393.108(a) that includes the binder and hooks. A 3/8"-1/2" lever binder rated 9,200 lb caps a 1/2" grade 70 chain at 9,200 lb, not 11,300 lb, so check the binder rating before buying up in chain size. Most flatbed freight runs fine on 5/16" or 3/8" G70; heavy equipment calls for 1/2" G70 or 3/8" and up in Grade 80. Retire any stretched, gouged or cracked link, weld splatter, heat discoloration or improper repair link - NACM minimum thickness is 0.297" at 5/16", 0.351" at 3/8", 0.460" at 1/2".

Worn-off embossing means a Grade 30 default rating at a CVSA roadside inspection. Never knot chain or use it as a shortener, and add edge protection where it crosses a sharp corner under 393.104(f).

Why Order Transport Chain from Fleet-Hero

Every Grade 70 chain lists the exact WLL and break strength right on the page-6,600 lb / 26,400 lb for the 3/8" x 20 ft assembly-with the gold chromate finish so you know the grade at a glance. Grade 80 assemblies sit right next to them if you need more capacity.

Matched ratchet binders (5/16"-3/8", 6,600 lb) and lever binders (3/8"-1/2", 9,200 lb) plus edge protectors go in the same cart. Local pickup is open in Addison, IL, and shipping runs to the Lower 48. Case quantities are ready for fleets that need to re-chain several trailers at once.

At Fleet-hero.com you will find transport chain trusted by flatbed drivers and fleets, with fast shipping to the Lower 48.