Fleet Hero

Steel & Flatbed Tarps

8 products

Browse Subcategories

All Steel & Flatbed Tarps Products

Filters

$
—
$

8 products

What Are Flatbed Tarps? 

A flatbed tarp is a cover you throw over an open-deck load so rain, road spray and gravel never touch the freight. The steel tarp is the low-drop version - flat, rectangular, cut for dense freight that hugs the deck. Drop follows width: a 16 ft tarp hangs 4 ft, 20 ft hangs 6, 24 ft hangs 8, 28 ft hangs 10.

Lumber tarps go deeper, 6–8 ft, with an end flap for tall stacks; steel tarps stay at 4 ft, flap optional.

Types of Flatbed and Steel Tarps We Carry 

  • 18 oz vinyl steel tarps - 20-21 mil PVC-coated polyester, the default for coil, plate and beam loads on flatbed trailers.

  • Lightweight ripstop steel tarps (11–15 oz) - about 10–15 lb lighter at 16x27 than 18 oz, and the ripstop weave stops a small cut from running.

  • Airbag / parachute-fabric steel tarps - vinyl top, nylon airbag sides, up to 40% lighter than all-vinyl 18 oz; sides are water-repellent, not waterproof.

  • With flap or no flap - a 4 ft x 8 ft end flap seals the front of the load; no-flap tarps fold simpler and carry less weight.

  • Size ladder - 16x20 is the classic 4 ft drop steel tarp; 20x24 is machinery class; 28x30 covers oversize. Width sets the drop, so both numbers get listed.

Flatbed Tarp Sizes, Fabric Weights and Specs

Flatbed tarps need exact size, weight and hardware counts so you know what you’re throwing on the deck.

Size

Drop

Fabric

D-ring rows

Approx. weight

16x20

4 ft

18 oz vinyl

2

55 lb

16x27

4 ft

18 oz vinyl

2

64–70 lb

16x27

4 ft

14 oz / ripstop

2

56–60 lb

20x24

6 ft

18 oz vinyl

3

75–83 lb

20x18

4 ft

airbag fabric

2

~43 lb

D-rings sit every 24" with box stitching and a pad underneath. Brass grommets every 2 ft, heat-sealed seams, cold-crack rated to -40°F. One 16–20 ft steel tarp covers about 20 ft of deck; a 2-piece set handles a 40 ft gooseneck.

Where Flatbed Drivers Use Steel Tarps 

Steel coils, plate, sheet, rods, cable reels, pipe bundles and structural beams are what a 4 ft drop steel tarp was cut for - dense, low freight with no extra fabric to fold. Taller stuff like machinery, castings or fabricated metal steps up to a 20x24 machinery tarp. Hotshot and gooseneck guys cover the whole deck with one 16x20.

On a 40 ft trailer you run two tarps; on a 48–53 ft flatbed, a three-piece set. Sharp edges eat vinyl, so corner protectors and coil cuffs go under the tarp before it ever touches steel.

How to Choose and Care for a Flatbed Tarp

Pick the drop by load height, not trailer length-4 ft for plate and coil, 6 ft for machinery, 8 ft only when the stack is lumber-high. A taller tarp works on steel but leaves extra fabric to fold. Lightweight or airbag builds save 10–25 lb every time you tarp by hand. Hook rubber tarp straps or bungees from the D-rings to the rub rail and stake pockets, work front to back so it doesn’t billow, and tuck the flaps tight.

Dry it before folding, keep it off the ground and out of the sun, patch cuts with tarp repair tape, and check seams monthly. A tarp helps meet 49 CFR 393.100(b) so cargo doesn’t spill or blow off, but it never replaces the chain and strap count.

Why Order Flatbed Tarps from Fleet-Hero

Ripstop fabric, heat-sealed seams, double-stitched hems. Brass grommets every 2 ft and two rows of D-rings on the 15 oz builds. Sizes that actually fit the deck-16x20, 20x24, 28x30-instead of stretching a lumber tarp over steel.

Winch straps, chain, binders, corner protectors and coil cuffs are already listed, so the whole setup goes in one cart. Local pickup at 500 S Lombard Road in Addison, IL, free local delivery on bigger orders.

At Fleet-hero.com you will find flatbed tarps sized for 40-53 ft decks when you need the tarp and the rest of the gear together.